REGATRON TC.ACS Скачать руководство пользователя

Страница: 4 / 66

Table of Contents

REGATRON

Performance. Precision. Quality.

TC.ACS - Device Manual (V04.60) - 26.4.2022

4 / 66

3.2.1 Overview .................................................................................................................................................... 19
3.2.2 Integrated Safety Relay (TC.ISR) ................................................................................................................ 21

3.2.3 Pin Definition of Interface X609 ................................................................................................................. 25

4 Installation and Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

4.2 Site Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

4.3 Case Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

4.4 Electrical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

4.4.1 Safety Advice ............................................................................................................................................. 29
4.4.2 Prerequisites .............................................................................................................................................. 30

4.4.2.1 Correct Size of Cables and Cable Ends ................................................................................................................. 30
4.4.2.2 Electromagnetic Compatibility of Cables ............................................................................................................ 31

4.4.3 Procedure .................................................................................................................................................. 31

4.5 Connecting a Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

4.5.1 Introduction ............................................................................................................................................... 32
4.5.2 Requirements to a Cooling System ............................................................................................................ 32

4.5.2.1  Specifications of the internal Heat Exchangerer   ................................................................................................. 32
4.5.2.2  Requirements to the Cooling Liquid  .................................................................................................................... 33
4.5.2.3  Pressure Differences and Flow Rates   .................................................................................................................. 34

4.5.3 Safety Advice ............................................................................................................................................. 34
4.5.4 Procedure .................................................................................................................................................. 34

4.6 Connecting a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

4.7 Connecting an external Signal Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

4.8 Starting the TC.ACS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

4.9 Running a Function Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

4.9.1 Prerequisites .............................................................................................................................................. 37

Содержание TC.ACS



































































Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды

REGATRON TC.ACS, Руководство по эксплуатации устройства

Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды