REGATRON TC.ACS Скачать руководство пользователя

Страница: 30 / 66

Installation and Commissioning

Electrical Installation

REGATRON

Performance. Precision. Quality.

TC.ACS - Device Manual (V04.60) - 26.4.2022

30 / 66

4.4.2 Prerequisites

For the electrical installation of the TC.ACS device the electrical cabinet or whatever the TC.ACS device is to be

connected to, must be galvanically isolated, disconnected from the mains and secured against being

reconnected.
Furthermore, the following must be given:
• Correct Size of Cables and Cable Ends

(

4.4.2.1

)

• E lectromagnetic Compatibility of Cables

(

4.4.2.2

)

4.4.2.1 Correct Size of Cables and Cable Ends

The terminals X10 (AC line input) and X20 (AC load output) (see

3.2

) allow for different types of cable ends, i.e.

the following:
• flexible cable ends
• rigid cable ends
• cable ferrules

In any case, the cable ends must meet the following conditions regarding their cross-section and their stripping
length:

Fig. 9:

Cable end with diameter

and stripping length

Cables carrying high currents must have an adequate cable cross-section area.

If necessary, refer to your national standards and the information on the type plates in order

to determine the correct size of cables.

Regatron recommends to use cable ferrules.

Clamp

Type of cable end

Cross-section area A (= π

/4)

Stripping length

AWG/kcmil

X20

Flexible

10 … 25

10 … 2

19 mm

Rigid

6 … 35

Ferrule

4 … 25

X10

All

25 … 50

2 … 0/1

22 mm

The touch current in the grounding cables exceeds the limit of 3.5 mA. Therefore the minimum

cross-section of the grounding cable must comply with the local safety regulations for
equipment with high current in the grounding cable. This is 10 mm

for fixed connection.

Содержание TC.ACS



































































Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды

REGATRON TC.ACS, Руководство по эксплуатации устройства

Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды