REGATRON TC.ACS Скачать руководство пользователя

Страница: 59 / 66

Option: TC.ACS.CANmp Interface

Application

REGATRON

Performance. Precision. Quality.

TC.ACS - Device Manual (V04.60) - 26.4.2022

59 / 66

12 Option: TC.ACS.CANmp Interface

12.1 Application

The TC.ACS.CANmp (CAN multiprotocol) interface (X652/X653) is a standard CAN interface according to ISO

11898; Layer 1 and 2 in the ISO/OSI layer model. It is designed to build a CAN bus for the communication between

the TC.ACS device and other devices.

The digital I/O interface (X654) provides additional digital inputs and outputs, which are programmable via

ACSControl.

Generally, to a CAN bus the following applies:
- The maximum possible bus length depends on the baud rate (e.g. 30 m @ 1 Mbit/s,

100 m @ 500 Kbit/s, ...).

- It is possible to connect 32 bus members. In case of distance reduction and transfer rate

reduction more bus members are possible.

- The bus end needs to be terminated with a resistance of 120 Ω. A corresponding terminal

resistor is supplied.

Содержание TC.ACS



































































Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды

REGATRON TC.ACS, Руководство по эксплуатации устройства

Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды