REGATRON TC.ACS Скачать руководство пользователя

Страница: 50 / 66

Option: Analog I/O Adaptor (TC.ACS X609 Adapter)

Interfaces on the Rear

REGATRON

Performance. Precision. Quality.

TC.ACS - Device Manual (V04.60) - 26.4.2022

50 / 66

10.3 Interfaces on the Rear

Tab. 7:

Interfaces of the analog I/O adaptor (rear)

10.4 Low Pass Filter

Each of the inputs and outputs can be individually filtered, if necessary. Here the filters are passive RLC second

order low pass filters with the following characteristics:
• f

-3dB

= 70.7 kHz

• Q = 0.51
• Damping ratio = 0.98
• No exaggeration in the frequency response
• No transient in step response

Whether or not an individual signal is filtered is determined by the position of a related jumper inside the adaptor

box. Here, the jumpers JU1 - 4 belong to the inputs AIN1 - 4 and the jumpers JU5 - 8 belong to the outputs

AOUT1-4. Each jumper can be set to one of two positions: 1/2 or 2/3.

Here, the following holds:
• Jumper is set to position 1/2 -> signal is filtered
• Jumper is set to position 2/3 -> signal is unfiltered

Interfaces on the rear of the analog I/O adaptor

Interface

Type

Function

X609

M12 flush-type

connector

female

Repetition of interface X609 of TC.ACS

X630

male

Connection to interface X609 of TC.ACS

Due to the damping ratio the -3 dB point is not at the cut-off frequency.

Содержание TC.ACS



































































Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды

REGATRON TC.ACS, Руководство по эксплуатации устройства

Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды