REGATRON TC.ACS Скачать руководство пользователя

Страница: 27 / 66

Installation and Commissioning

Site Conditions

REGATRON

Performance. Precision. Quality.

TC.ACS - Device Manual (V04.60) - 26.4.2022

27 / 66

4.2 Site Conditions

CAUTION

Electric surge!

The system is designed for use in LPZ1 (Lightning Protection Zone 1).

CAUTION

Overheating!

Make sure that the warm exhaust air is not drawn back into the system.

Installation conditions

Over voltage category (according to EN 62477-1)

Distance at the front

to the nearest wall or large

surface area body

> 850 mm
For access to the front as well as for

drawing in the cooling air

NOTE: If there is a cabinet door, an

escape route of > 600 mm width must

be provided in front of the open door.

This is independent of the 850 mm

distance.

Distance at the rear

to the nearest wall or large

surface area body

> 850 mm
For access to the rear, as well as for

exhaust of the cooling air

NOTE: If there is a cabinet door, an

escape route of > 600 mm width must

be provided behind the open door.

This is independent of the 850 mm

distance.

Environmental conditions

Maximum altitude

2000 meters above sea level

Temperature

-5°C...40°C

Humidity

0...95%

Moisture condition of the skin (according to EN 62477-1)

Dry

Vibrations (according to IEC-60068-2-6)

Test Fc

Pollution degree (according to EN 62477-1)

Environmental operating conditions (according to IEC 60721-3-3)

Climate

3K22

Pollution degree

see above

Special climatic conditions

3Z1

Mechanically active substances 3S5
Mechanical

3M11

Biological

3B1

Содержание TC.ACS



































































Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды

REGATRON TC.ACS, Руководство по эксплуатации устройства

Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды