REGATRON TC.ACS Скачать руководство пользователя | Manualshive

Страница: 54 / 66

background image

Option: Liquid to Air Heat Exchanger TC.LAE

Installation and Commissioning

REGATRON

Performance. Precision. Quality.

TC.ACS - Device Manual (V04.60) - 26.4.2022

54 / 66

11.3.5 Filling of Cooling Liquid

11.3.5.1 Safety Advice

11.3.5.2 Prereqisites

For the filling of cooling liquid to the cooling circuit the following must be given:
• Both the TC.ACS device and the TC.LAE device are in horizontal position.
• Both the TC.ACS device and the TC.LAE device are switched off.
• The following material is provided:



Regatron AG fill-up kit, including: 2,5 l cooling liquid Antifrogen® N 30%, 1 funnel, 2 hoses with fittings

attached



Collection vessel



Absorbent cloth or paper



6 mm Allen wrench

You can order cooling liquid directly from the retailer Clariant. The product is named

Antifrogen® N 30%.

If necessary see

for

Emptying of Cooling Liquid

.

WARNING

Possible harm by cooling liquid!

According to the GHS the recommended cooling liquid Antifrogen® N 30% is classified as being

hazardous in the following ways:
- Harmful if swallowed (H302)
- May cause damage to organs through prolonged or repeated exposure (H373)

Avoidance:

When handling with cooling liquid, do the following:
- pay attention to the warning signs on the product.
- open doors and windows and ensure the room is well ventilated also on the ground level.
- use respiratory protection and protective cloves which are resistant against solvents.
- close cooling liquid vessels immediately.
- keep out of the reach of children.
- avoid contact with skin and eyes.

If exposed or concerned: Get medical advice!

CAUTION

Damage of the Device!

A short circuit may occur due to moisture (cooling liquid) in the device.

Avoidance:

- Make sure that both the TC.ACS device and the TC.LAE device are switched off.

- Keep the cooling liquid from spilling on and into the devices.

«
...
52
53
54
55
56
...
»

Содержание TC.ACS



































































Отзывы:

Нет отзывов

Похожие инструкции для TC.ACS

Бренд: Cairox Страницы: 8

Бренд: Eastwood Страницы: 12

Бренд: Eastwood Страницы: 8

Бренд: Earlex Страницы: 8

Бренд: Earlex Страницы: 5

Бренд: Fein Страницы: 117

Бренд: Fein Страницы: 103

Бренд: Feider Machines Страницы: 14

Бренд: Ratio Electric Страницы: 4

SourceMeter 2470

Бренд: Keithley Страницы: 86

Бренд: Keithley Страницы: 38

Бренд: Makita Страницы: 1

Бренд: Porter-Cable Страницы: 15

Бренд: YATO Страницы: 80

Бренд: Wacker Neuson Страницы: 30

Бренд: H&H Страницы: 14

Бренд: 9circle Страницы: 14

Бренд: HySecurity Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды