REGATRON TC.ACS Скачать руководство пользователя

Страница: 26 / 66

Installation and Commissioning

Overview

REGATRON

Performance. Precision. Quality.

TC.ACS - Device Manual (V04.60) - 26.4.2022

26 / 66

4 Installation and Commissioning

4.1 Overview

The installation and commissioning of the TC.ACS includes the following steps:
• Case Installation (

4.3

)

• Electrical Installation (

4.4

)

• Connecting a Cooling System (

4.5

)

• Connecting a PC (

4.6

)

• Connecting an external Signal Generator (

4.7

)

• Starting the TC.ACS (

4.8

)

• Running a Function Test (

4.9

)

DANGER

Electric shock!

Avoidance:

Without the optional discharge feature XCDBox, mobile operation is not permitted!

Connecting an external Signal Generator

is necessary only if you want to operate the TC.ACS

device in

Amplifier Mode

(see

2.1.2

For installing and commissioning the

Option: Liquid to Air Heat Exchanger TC.LAE

see

11.3

, if

necessary.

The TC.ACS device is to be used exclusively as a built-in device in a cabinet system. Here, the

basic protection of the connection terminals must be provided in the end application, so that

IP20 applies.

With respect to the installation location the site conditions (see

4.2

) have to be regarded.

Содержание TC.ACS



































































Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды

REGATRON TC.ACS, Руководство по эксплуатации устройства

Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды