REGATRON TC.ACS Скачать руководство пользователя

Страница: 36 / 66

Installation and Commissioning

Starting the TC.ACS

REGATRON

Performance. Precision. Quality.

TC.ACS - Device Manual (V04.60) - 26.4.2022

36 / 66

4.8 Starting the TC.ACS

4.8.1 Safety Advice

4.8.2 Prerequisites

For starting the TC.ACS, the following must be given:
• The device is electrically installed (see

4.4

• A cooling system is connected (see

4.5

) and it is running.

4.8.3 Procedure

To start the TC.ACS, do the following:



Switch on the main switch (see

3.1



The device boots and a device self-test is performed.



When finished, the LED for POWER (see

3.1.2

) lights up.

DANGER

Electric shock!

Avoidance:

- Device and load must be isolated against accidental contact.
- No maintenance work must be carried out.
- Warning signs must be used and the area must be cordoned off.

CAUTION

Possible damage to the device!

Due to condensation inside the device or on the supply tube of the cooling system.

Avoidance:

- If there is any water condensation, it will show on the rear side of the device (especially

between the input and the output interface for cooling circuit (see

3.2

). Check visually and

if so, do not start the device.

- Keep the inlet temperature of the cooling liquid at a temperature level above the dew

point. For the relevant dew point refer to a dew point table.

Damage to the device due to condensed water is excluded from the warranty.

If any other LED also lights up or flashes, then there is a warning or an error. Detailed

information is provided by the software ACSControl.

Содержание TC.ACS



































































Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды

REGATRON TC.ACS, Руководство по эксплуатации устройства

Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды