REGATRON TC.ACS Скачать руководство пользователя

Страница: 32 / 66

Installation and Commissioning

Connecting a Cooling System

REGATRON

Performance. Precision. Quality.

TC.ACS - Device Manual (V04.60) - 26.4.2022

32 / 66

4.5 Connecting a Cooling System

4.5.1 Introduction

In order to dissipate the generated heat, the TC.ACS is equipped with an internal heat-exchanger. This heat

exchanger necessarily needs to be connected to an external cooling system.

4.5.2 Requirements to a Cooling System

The requirements to a cooling system are given by the following:
• Specifications of the internal Heat Exchangerer (

4.5.2.1

)

• Requirements to the Cooling Liquid (

4.5.2.2

)

• Pressure Differences and Flow Rates (

4.5.2.3

)

4.5.2.1 Specifications of the internal Heat Exchanger

The

Option: Liquid to Air Heat Exchanger TC.LAE

is designed to be used as an external cooling

system with the TC.ACS.

Any other external cooling system has to to meet specific requirements (see

4.5.2

CAUTION

Possible damage to the device!

Due to condensation inside the device or on the supply tube.

Avoidance:

Keep the inlet temperature of the cooling liquid at a temperature level above the dew point.

For the relevant dew point refer to a dew point table.

Damage to the device due to condensed water is excluded from the warranty.

General specifications

Connections

G1/2” (see

3.2

)

Heat sink material

EN AW-5083

Thermal rating

5 kW

Approx. thermal resistance

< 0.01 K/W

Performance data with a cooling liquid with a specific heat capacity of 4.19 kJ/kgK

Recommended flow rate

5 l/min

Min. flow rate

2.5 l/min

Max. inlet temperature

25 °C @ 2.5 l/min, 50 °C @ 8 l/min

Содержание TC.ACS



































































Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды

REGATRON TC.ACS, Руководство по эксплуатации устройства

Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды