REGATRON TC.ACS Скачать руководство пользователя | Manualshive

Страница: 28 / 66

background image

Installation and Commissioning

Case Installation

REGATRON

Performance. Precision. Quality.

TC.ACS - Device Manual (V04.60) - 26.4.2022

28 / 66

4.3 Case Installation

The TC.ACS is intended to be installed in a standard 19” switch cabinet with an external air flow. In this case it is to

be placed on rails or shelves and fastened at the holes on the left and right edges of the front panel. Usually M6

screws can be used.

Fig. 8:

Case installation with the help of a trolley

CAUTION

Possible damage!

- Due to soiling and foreign bodies at the installation location
- Due to a build-up of heat

Avoidance:

- The installation location must be free of conductive and aggressive substances as well as

moisture.

- No foreign bodies such as drilling swarf or screws are to be allowed to fall into the system.
- The site conditions (see technical datasheet) must be met.
- The ventilation openings on the front panel and rear wall of the devices must not be

covered or sealed.

Due to the weight of the device the following is to be regarded:
- Rails or shelves must be robust.
- The case for a TC.ACS must be in contact over full installation depth.
- At the rear a cross-member must be installed for additional fastening.

«
...
26
27
28
29
30
...
»

Содержание TC.ACS



































































Отзывы:

Нет отзывов

Похожие инструкции для TC.ACS

Бренд: TDK-Lambda Страницы: 29

Бренд: Fein Страницы: 70

Бренд: Jet Страницы: 12

Бренд: VATTON Страницы: 20

Бренд: Grizzly Страницы: 48

SMA 50 BER-13.G1

Бренд: Gerima Страницы: 24

ProJet Cart Station

Бренд: 3D Systems Страницы: 21

Бренд: Promaker Страницы: 24

Бренд: SharpX Страницы: 16

Бренд: Klauke Страницы: 22

Бренд: Parkside Страницы: 43

Бренд: Sealey Страницы: 3

Бренд: Proluxe Страницы: 17

Бренд: B+K precision Страницы: 15

Бренд: Kinetik Страницы: 8

Бренд: Ratio Страницы: 48

Бренд: Daewoo Страницы: 24

PPH SS 670 PENDULUM ACTION JIGSAW

Бренд: Parkside Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды