REGATRON TC.ACS Скачать руководство пользователя

Страница: 20 / 66

Interfaces, Controls and Displays

Interfaces on the Rear Side

REGATRON

Performance. Precision. Quality.

TC.ACS - Device Manual (V04.60) - 26.4.2022

20 / 66

)

Interfaces on the rear side

X112-2

ISR interface

NOTE: The interface must be terminated with the dummy plug X112, if not used. For more

information see

3.2.2

X601/

X602

Preset distribution interfaces (only used for multi-unit-systems)

NOTE: In single device use one of these interfaces must be terminated with 100 ohms.

Bay for optional interface cards, e.g. Option: Digital I/O Interface (TC.ACS.DIG8IOST) (see

) or Option:

TC.ACS.CANmp Interface (see

)

X605

Ethernet-LAN interface to connect to a PC

X604

EtherCAT output interface (only used for multi-unit systems)

X603

EtherCAT input interface (only used for multi-unit systems)

X607

USB-Interface to connect to a PC

X608

Micro SD card slot (only for service)

X620

Trigger input

NOTE: For configuring the trigger input please contact Regatron Customer Support.

X621

Trigger output

NOTE: The trigger output can be configured via the software ACSControl (see the related software

manual).

X609

Analog input and output for general usage

NOTE: To use the interface you need a specific plug.
- Manufacturer: PHOENIX CONTACT AG
- Order number: 1430048
- REGATRON item number: 452-01244

For the pin definition see

3.2.3

Outlet interface for cooling circuit (thread: G1/2” with connection fitting

)

X10

AC line input terminal (L1, L2, L3)

Additional earthing stud

NOTE: Due to high leakage current the additional earthing stud must be connected to earth.

X20

AC load output terminal (L1, L2, L3, N, PE)

NOTE: Due to high leakage current the PE clamp must be connected to earth.

Inlet interface for cooling circuit (thread: G1/2” with connection fitting

)

NOTE: The figure above shows the standard version. As an option, the following interfaces may be replaced

by a senseboard (see

X606

Service interface RS232 (only used for software update)

NOTE: This interface requires a cable with braided shield.

X613

Digital input interface (currently not supported)

X612

Signal input for phase L3 on the load side

for

Connecting an external Signal

Generator

X611

Signal input for phase L2 on the load side

X610

Signal input for phase L1 on the load side

Содержание TC.ACS



































































Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды

REGATRON TC.ACS, Руководство по эксплуатации устройства

Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды