REGATRON TC.ACS Скачать руководство пользователя

Страница: 43 / 66

Maintenance and Support

Maintenance

REGATRON

Performance. Precision. Quality.

TC.ACS - Device Manual (V04.60) - 26.4.2022

43 / 66

7 Maintenance and Support

This section includes the following subsections:
• Maintenance (

7.1

)

• Support (

7.2

)

7.1 Maintenance

The TC.ACS device is generally maintenance-free. However, the following measures may be needed:
• Adjusting the Accuracy of the Output Values (

7.1.1

)

• Updating the Firmware (

7.1.2

)

• Replacing the Batteries of the Real-time-Clock in the Controller Board (

7.1.3

)

7.1.1 Adjusting the Accuracy of the Output Values

The accuracy of the device output values can be adjusted by Regatron AG. If necessary, please contact

[email protected].

7.1.2 Updating the Firmware

You can update the firmware of the TC.ACS device via the software ACSControl, if necessary. For more

information see the related software manual.

7.1.3 Replacing the Batteries of the Real-time-Clock in the Controller Board

The life expectancy of the batteries of the real-time-clock in the controller board is approx. 10 years at room

temperature. You can replace the batteries by yourself. Please contact [email protected].

For the maintenance of the

Option: Liquid to Air Heat Exchanger TC.LAE

see

11.4

, if

necessary.

Содержание TC.ACS



































































Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды

REGATRON TC.ACS, Руководство по эксплуатации устройства

Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды