REGATRON TC.ACS Скачать руководство пользователя

Страница: 52 / 66

Option: Liquid to Air Heat Exchanger TC.LAE

Interfaces, Controls and Displays

REGATRON

Performance. Precision. Quality.

TC.ACS - Device Manual (V04.60) - 26.4.2022

52 / 66

11.2 Interfaces, Controls and Displays

Fig. 18:

Interfaces, controls and displays (rear side)

11.3 Installation and Commissioning

11.3.1 Overview

The installation and commissioning of the TC.LAE includes the following steps:
• Case Installation (

11.3.2

)

• Setting up the Cooling Circuit (

11.3.3

)

• Connecting the TC.LAE to the Mains (

11.3.4

)

• Filling of Cooling Liquid (

11.3.5

)

• Starting the Pump of the TC.LAE (

11.3.6

)

Interfaces, controls and displays (rear side)

Interface

Outlet

(thread: G1/2”)

Interface

Inlet

(thread: G1/2”)

Interface

Fill

(thread: G1/2”)

NOTE: For practical reasons these interfaces are

duplicated on the top.

Interface

Ventilate

(thread: G1/2”)

Mains connection

Pump switch

(pushed) on the front and rear: Pump is on

(pushed) on the front and/or rear: Pump is off

NOTE: The pump switch is duplicated on the front side.

If necessary, see

11.3.7

for

Emptying of Cooling Liquid

Содержание TC.ACS



































































Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды

REGATRON TC.ACS, Руководство по эксплуатации устройства

Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды