REGATRON TC.ACS Скачать руководство пользователя

Страница: 37 / 66

Installation and Commissioning

Running a Function Test

REGATRON

Performance. Precision. Quality.

TC.ACS - Device Manual (V04.60) - 26.4.2022

37 / 66

4.9 Running a Function Test

With the software ACSControl you can run a function test on the TC.ACS to confirm that it actually works as

intended.

4.9.1 Prerequisites

For running a function test, the following must be given:
• The TC.ACS is connected to a PC (see

4.6

• The TC.ACS has been started (see

4.8

• The software ACSControl is running and it is connected to the TC.ACS.
• The TC.ACS has no error.

4.9.2 Procedure

To run a function test, do the following via the software ACSControl:



Open the tab

Basic Waveform Generator



Specify amplitude, voltages, frequency and number of phases in the respective fields



In the toolbar, click on



On the front of the TC.ACS the LED for VOLTAGE ON (see

3.1.2

) lights up.

For installing the software ACSControl as well as detailed information on how to use it, see the

related software manual.

If there is a warning or an error, detailed information is provided by the software ACSControl

Содержание TC.ACS



































































Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды

REGATRON TC.ACS, Руководство по эксплуатации устройства

Результаты поиска

Содержание TC.ACS

Отзывы:

Похожие инструкции для TC.ACS

Бренды по названию

Популярные бренды