Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 124

Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 9

FASTRAK MANUAL

Rev. G

4

JUNE 2012

Figure 1-7 DC USB Cable Installation

7.

Install the Host Software

NOTE:

FASTRAK Host Software is intended to be installed on a computer running

Windows XP/Vista/Win 7 only.

•

Insert the FASTRAK Host Software CD-ROM into your computer’s CD-ROM drive.

•

If the FASTRAK Host Software Installation Panel does not run automatically, then
navigate to the CD-ROM drive using Windows Explorer. Run “Setup.exe”. The Host
Software Installation Panel will appear. Select “Install Host Software.” The installation
wizard will walk you through the installation.

•

For simplicity, it is recommended that you use the default installation settings
suggested by the installation wizard.

•

When the installation is complete, if you are planning to use your computer’s USB port
to connect to the FASTRAK System, leave the CD-ROM in the drive. It will be needed
when the initial USB connection is made.

•

If you are not planning to use the USB port, you may remove the CD-ROM from the
drive now.

USB Driver Installation

•

When FASTRAK is connected via USB to a Windows host for the first time, the host
will display a “Found New Hardware” message. The host will then launch the “Found
New Hardware Wizard” to locate and install the USB drivers for FASTRAK.

•

If the CD-ROM is not already in the drive, load it now.

•

When the Found New Hardware Wizard displays, select the “Install software
automatically” option and then “Next.”

•

The wizard will install the FASTRAK Loader. When it has completed, select “Finish.”

•

The same process will be launched again automatically to install the Polhemus
FASTRAK USB Driver. Repeat the same selections and the process will be complete.

«
...
7
8
9
10
11
...
»

Содержание 3SPACE FASTRAK





























































































































Отзывы:

Нет отзывов