Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 124

Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 72

FASTRAK MANUAL

Rev. G

67

JUNE 2012

‘r’ – Transmitter Mounting Frame

Syntax:

r

station

,[

A

],[

E

],[

R

]<>

or

r

station

<> to read back the current transmitter mounting frame

Purpose:

This command allows the user to modify the mounting frame coordinates of the
transmitter relative to a particular receiver. It is basically a non-physical rotation
of the transmitter and becomes the new orientation reference for the specified
receiver’s measurements. The command parameters are as follows:

station

the station to be defined

A

azimuth mounting frame angle

E

elevation mounting frame angle

R

roll mounting frame angle

Relatives:

None.

Default:

0,0,0

Example:

If there was a requirement to mount the transmitter upside down, (more
mechanically feasible) then the following command should be used.

r1,0,0,180<>

The orientation measurements for station 1 will now look as if the transmitter had
not been mounted upside down.

RECORD IDENTIFIER ........ r

INITIATING COMMAND ....... r

byte(s)

Identification

Format

1 ...

Record type, “2”

A1

2 ...

Station Number

A1

3 ...

Sub-record type ‘r’

A1

4-11 ...

Azimuth mounting frame angle

Sxxx.xxx

12-19 ...

Elevation mounting frame angle

Sxxx.xxx

20-27 ...

Roll mounting frame angle

Sxxx.xxx

28-29 ...

Carriage return, line feed

«
...
70
71
72
73
74
...
»

Содержание 3SPACE FASTRAK





























































































































Отзывы:

Нет отзывов