Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 89

Страница: 89 / 124

FASTRAK MANUAL

Rev. G

JUNE 2012

Designate one FASTRAK system as the master and the other as the slave.

NOTE:

Make sure that the two FASTRAKs have different colored dots on

them so you will know that they are operating at different frequencies.

Connect one end of the sync cable to the “sync out” receptacle of the master
FASTRAK.

Connect the other end of the sync cable to the “sync in” receptacle of the slave
FASTRAK.

Send the command y0<> to the master FASTRAK.

Send the command y1<> to the slave FASTRAK.

The two systems will now be synced together.

NOTE:

Although synchronization

allows two FASTRAKs to operate in relatively close proximity, make sure the
receiver of one system does not get closer to the transmitter of the other system
than it is to the transmitter of its own system.

See

Multiple Systems

(page

) for multiple systems synchronization.

RECORD IDENTIFIER ........ y

INITIATING COMMAND ....... y

byte(s)

Identification

Format

1 .....

Record type, “2”

2 .....

Blank

3 .....

Sub-record type ‘y’

4 .....

Synchronization mode

0 - none - free run

1 = External

2 = CRT

5-6 .....

Carriage return, line feed

Содержание 3SPACE FASTRAK





























































































































Результаты поиска

Содержание 3SPACE FASTRAK

Отзывы:

Polhemus 3SPACE FASTRAK, Руководство пользователя, Страница: 89 / 124

Результаты поиска

Содержание 3SPACE FASTRAK

Отзывы: