manualshive.com logo in svg

Polhemus 3SPACE FASTRAK, Руководство пользователя, Страница: 68 / 124

Поделиться
Скачать
Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 68

 

FASTRAK MANUAL

 

 

Rev. G 

63 

JUNE 2012 

‘P’ – Single Data Record Output 

Syntax:

 

P 

Description:

  Output transmit mode refers to whether the system automatically transmits data 

records to the host (continuous output mode), or the host must request data 
records by sending a command to the system each time  (non-continuous output 
mode). 

Purpose:

 

In non-continuous output mode, this command requests a single data record to be 
transmitted to the host. If more than one station is enabled, then data from each 
active station will be displayed in numerical order (station 1 first, station 2 
second, etc. That is, a complete cycle of active stations will be output.)  

Relatives:

 

C, c 

Default:

 

Continuous output mode is disabled 

Example:

 

If the system is being used in an application where data is only needed a certain 
number of times, then the single data record output should be used. To request a 
single data record from the system, send the command as follows: 

 

 

P 

 

One data record from the FASTRAK system will be sent across the serial port to 
the host computer. 

 

 

Содержание 3SPACE FASTRAK





























































































































Отзывы:

Нет отзывов