manualshive.com logo in svg

Polhemus 3SPACE FASTRAK, Руководство пользователя, Страница: 2 / 124

Поделиться
Скачать
Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 2

 

FASTRAK MANUAL

 

 

Rev. G 

ii 

JUNE 2012 

 

Copyright © 2000-2012 by Polhemus 
Colchester, Vermont U.S.A. 

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or 
transmitted, in any form or by any means, mechanical, photocopying, recording or otherwise, without the 
prior written permission of Polhemus. No patent liability is assumed with respect to the use of the 
information contained herein. While every precaution has been taken in the preparation of this book, 
Polhemus assumes no responsibility for errors or omissions. Neither is any liability assumed for damages 
resulting from use of the information contained herein. 

3SPACE

® 

and FASTRAK

®

 are registered trademarks of Polhemus. 

Polhemus is a Good Manufacturing Practices (GMP) Contract Manufacturer under U.S. FDA 
Regulations. We are not a manufacturer of Medical Devices. Polhemus systems are not certified 
for medical or bio-medical use. Any references to medical or bio-medical use are examples of what 
medical companies have done with the Products after they have obtained all necessary or 
appropriate medical certifications. The end user/OEM/VAR/Distributor must comply with all 
pertinent FDA/CE regulations pertaining to the development and sale of medical devices and all 
other regulatory requirements. 

FCC Statement 

This equipment has been tested and found to comply with the limits for a Class A digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
interference when the equipment is operated in a commercial environment. This equipment generates, 
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the 
instruction manual, may cause interference to radio communications. Operation of this equipment in a 
residential area is likely to cause interference in which case the user will be required to correct the 
interference at the user’s expense. 

EC-Declaration of Incorporation 

For all FASTRAK models produced as of January 2012, this product conforms to the following 
European Community Directives: 

EMC Directive 2004/108/EC 
LVD 2006/95/EC 

The following standards were used to verify compliance with the directives: 

EMC: 

EN 61326-1:2006 EMC requirements 

 

 

Class A (Emissions) 

 

 

Class A (Harmonics) 

 

EN 55011:1998/A1:1999/A2:2002 (Radiated & Conducted Emissions) 

NOTE:  

The conducted emission here-in only applies if a Polhemus supplied power 
supply is used with the FASTRAK electronics unit. 

 

EN 61000-3-2:2000 (Harmonics) 

 

EN 61000-3-3:1995/A1:2001 (Flicker) 

 

EN 61000-4-2:1995/A1:1998/A2:2001 (ESD) 

 

EN 61000-4-3:2002 (Radiated RF Immunity) 

 

EN 61000-4-4:2004 (Electrical Fast Transient/Burst) 

 

EN 61000-4-5:1995 (Surge Immunity) 

 

EN 61000-4-6:1996 (Conducted RF Immunity) 

 

EN 61000-4-11:2004 (Voltage Dips & Interruptions) 

 

 

Содержание 3SPACE FASTRAK





























































































































Отзывы:

Нет отзывов