manualshive.com logo in svg

Polhemus 3SPACE FASTRAK, Руководство пользователя, Страница: 23 / 124

Поделиться
Скачать
Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 23

 

FASTRAK MANUAL

 

 

Rev. G 

18 

JUNE 2012 

 

Figure 7-4 Sync Connector Identification (Input and Output) 

NOTE:  If a ground is required, use a shielded cable and use the shield as the ground 

reference. 

7.7 Frequency Select Module  

The Frequency Select Module is used to select the operating carrier frequency of the FASTRAK 
system. It is located inside the SEU, directly behind the Transmitter input connector. The 
alternate carrier frequencies are produced by inserting the required tuning module in the socket 
provided. The Frequency Select Modules are color coded for carrier frequency identification as 
described in 

Carrier Frequency

, page 

13

.  

IMPORTANT NOTE: As with any handling of an electronics printed circuit board (PCB), when 
inserting other frequency select modules to change the carrier frequency, static electricity 
precautions must be observed. Do not remove and replace frequency select modules with power 
applied to the SEU. Also, do not handle or touch the main PCB without first being grounded at 
an “ESD-safe” workstation. 

7.8 RS-232 I/O 

The RS-232 I/O serial connector is a standard, 9 pin, male, “D type” connector located on the 
rear panel of the SEU as shown in 

Figure 7-2

 on page 

15

. The pinout identification for this 

connector is as follows: 

FASTRAK End  

User End 

 

1 

Not used 

 

2 

RxD (Receive Data)  -----------------------------------    TxD (Transmit Data to the FASTRAK) 

 

3 

TxD (Transmit Data)  ----------------------------------   RxD (Receive Data from the FASTRAK) 

 

4 

Not used 

 

5 

GND  ------------------------------------------------------   GND 

 

6 

Not used 

 

7 

Not used 

 

8 

Not used 

 

9 

Not used 

 

Содержание 3SPACE FASTRAK





























































































































Отзывы:

Нет отзывов