Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 124

Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 75

FASTRAK MANUAL

Rev. G

70

JUNE 2012

‘T’ – Built-In-Test Information

Syntax:

TBIT

number

[,0]<>

Purpose:

This command allows the user to obtain additional information about a particular
BIT and clear a BIT error. The additional information is meaningful only to
factory personnel. The ‘T’ command is useful to attempt to clear a problem;
however, if an error re-occurs, and after you have verified your setup
configuration, consultation with the factory is recommended. The parameters are:

BIT

number

The BIT number for which added information is requested (see

below).

0 This parameter, if used, is specified as a 0 (zero). If present the

BIT

number

specified is reset/cleared.

Relatives:

S

Default:

N/A

Example:

BIT number Code

Transmitter & Receiver Error Codes

65

A

X Driver Linearity

66

B

Y Driver Linearity

67

C

Z Driver Linearity

68

D

x Gain Linearity

69

E

y Gain Linearity

70

F

z Gain Linearity

71

G

X Slope of Driver X Linearity Line

72

H

Y Slope of Driver Y Linearity Line

73

I

Z Slope of Driver Z Linearity Line

74

J

X Slope of Coil / Receiver X Linearity

75

K

Y Slope of Coil / Receiver Y Linearity

76

L

Z Slope of Coil / Receiver Z Linearity

77-83

Not Used (Reserved for future use)

84

T

Receiver PROM Error

85

U

Transmitter PROM Error

86

V

Receiver PROM Circuit Error

87

W

Transmitter PROM Circuit Error

88

X

Driver Characterization Validity

89

Y

Receiver Characterization Validity

90

Z

Receiver Coil Validity

«
...
73
74
75
76
77
...
»

Содержание 3SPACE FASTRAK





























































































































Отзывы:

Нет отзывов