manualshive.com logo in svg

Polhemus 3SPACE FASTRAK, Руководство пользователя, Страница: 24 / 124

Поделиться
Скачать
Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 24

 

FASTRAK MANUAL

 

 

Rev. G 

19 

JUNE 2012 

 

Figure 7-5 RS-232 Cable Connection 

NOTE:

 Many commercially available cables do not include connections for all pins, so do not 

assume that these connections are made. Please refer to 

APPENDIX F

: 

Cable Diagrams

 on page 

F-1

 to find the specific interconnection scheme for your host computer in order to obtain a 

reliable serial interface. 

If you do not find your particular host’s RS-232 I/O interconnection scheme in 

APPENDIX F

: 

Cable Diagrams

 on page 

F-1

, refer to 

Contacting Polhemus Customer Service

 on page 

8

 and 

FAX a copy of your host computer’s pin out identification from its user’s manual. Polhemus will 
respond with advice on how to make the serial connection between your FASTRAK and your 
host computer.  

NOTE: THE FASTRAK SYSTEM BEHAVES AS A TRANSMITTER ON THE RS-232 
AND THEREFORE A NULL MODEM CABLE IS REQUIRED.

 

7.9 USB I/O 

The USB I/O connector is a standard Series B connector located on the rear panel of the 
FASTRAK SEU as shown in 

Figure 7-2

 on page 

15

. The connector on the FASTRAK is a square 

shaped connector with two corners shaved off for correct orientation upon insertion. The 
connector on the host PC is a Series A connector and is rectangular shaped. Since the connectors 
on each end of the USB cable are different, it is impossible to connect the cable incorrectly. The 
signals on the FASTRAK USB connector conform to the USB standard. The USB 
communication cable used to connect the FASTRAK to the host computer is a standard cable 
that is commercially available. 

7.10 Optional RS-422 I/O  

The optional RS-422 connector is identical to the RS-232 connector in form, fit, function, and 
location on the rear of the SEU. 

IMPORTANT NOTE:

 In order to use this interface, the FASTRAK system must be ordered 

from the factory configured for RS-422 communication. A system can be configured for RS-422 

Содержание 3SPACE FASTRAK





























































































































Отзывы:

Нет отзывов