manualshive.com logo in svg

Polhemus 3SPACE FASTRAK, Руководство пользователя, Страница: 46 / 124

Поделиться
Скачать
Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 46

 

FASTRAK MANUAL

 

 

Rev. G 

41 

JUNE 2012 

‘C’ – Continuous Output Mode 

Syntax: 

C 

Description:

  Output transmit mode refers to whether the system automatically transmits data 

records to the host (continuous mode), or the host must request data records by 
sending a command to the system each time (non-continuous mode). 

Purpose:

 

This command enables the continuous print output mode. When the system is in 
continuous mode, the data points from all stations are requested automatically and 
are scrolled one after the other in a continuous “stream”. If more than one station 
is enabled, then the data from each station will be displayed in numerical order 
(station 1 first, station 2 second, etc).  

Relatives:

 

c, P 

Default:

 

Continuous output mode is disabled. 

Example:

 

If the system is being used in an application where a fast update rate is critical, 
(driving real-time computer graphics, e.g. an animated character) then the 
continuous output configuration should be enabled. To enable continuous output 
mode, send the command as follows: 

C 

Data from the FASTRAK will now scroll continuously across the serial port to 
the host computer.  

 

Содержание 3SPACE FASTRAK





























































































































Отзывы:

Нет отзывов