manualshive.com logo in svg

Polhemus 3SPACE FASTRAK, Руководство пользователя, Страница: 20 / 124

Поделиться
Скачать
Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 20

 

FASTRAK MANUAL

 

 

Rev. G 

15 

JUNE 2012 

7. Component Description 

7.1 SEU 

The System Electronics Unit (SEU) is a stand-alone unit that may be located anywhere that is 
convenient to the work area, AC power and the host computer. It contains the required input and 
output connectors and controls to support up to four receivers, a single transmitter and the 
RS-232 and USB output ports. Receiver Input(s), Transmitter Input, I/O Cables, I/O Select 
Switch, External Sync I/O, Video Sync Input, and Power Input connections are located on the 
SEU as shown in 

Figure 7-1

 and 

Figure 7-2

, 

below

. 

 

Figure 7-1 FASTRAK SEU, Front View 

 

Figure 7-2 FASTRAK SEU, Rear View 

7.2 Transmitter Port 

The single Transmitter receptacle port is a 15 pin, male “D” type connector located on the front 
of the SEU as shown in 

Figure 7-1

. The transmitter should be connected to the SEU before the 

unit is powered on and disconnected after the unit is powered off. 

CAUTION: 

Do not 

disconnect the transmitter while the FASTRAK SEU is powered on. Also, do not power on the 
SEU without a transmitter connected. When routing cables, please be sure the transmitter cable is 
routed separately from the receiver cables.  

Содержание 3SPACE FASTRAK





























































































































Отзывы:

Нет отзывов