Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 124

Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 54

FASTRAK MANUAL

Rev. G

49

JUNE 2012

‘G’ – Boresight Reference Angles

Syntax:

G

station

,[Az

ref

],[El

ref

],[Rl

ref

]<>

or

G

station

<> to read back the current boresight reference angles

Purpose:

This command establishes the bore-sight reference angles for a particular station.
When the system is boresighted with the

‘B’ – *Boresight

command (see page

), the line-of-sight vector (Azimuth, Elevation, and Roll angles) will assume

these values. If all the optional parameters are omitted, the system returns the
boresight reference angles for the specified station as an output record of type ‘G’.
The command parameters are defined as:

station

the number of the station whose reference angles are to be fixed.

Az

ref

the azimuth reference angle.

El

ref

the elevation reference angle.

Rl

ref

the roll reference angle.

Relatives:

B, b

Default:

The system default boresight reference values are: 0, 0, 0

Example:

The user may wish to set the boresight reference values to an orientation that
corresponds with the application. For example, if the application required an
output of 0, -15, 0 following a boresight, reference angles should be applied with
the G command:

G1,0,-15,0<>

The boresight command (B1<>) will now cause the azimuth, elevation, and roll
data output to be 0, -15, 0 respectively.

SUB-RECORD IDENTIFIER .... G

INITIATING COMMAND ....... G

byte(s)

Identification

Format

1 ...

Record type, “2”

A1

2 ...

Station Number

A1

3 ...

Sub-record type ‘G’

A1

4-10 ...

Azimuth reference angle

Sxxx.xx

11-17 ...

Elevation reference angle

Sxxx.xx

18-24 ...

Roll reference angle

Sxxx.xx

25-26 ...

Carriage return, line feed

«
...
52
53
54
55
56
...
»

Содержание 3SPACE FASTRAK





























































































































Отзывы:

Нет отзывов