Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 124

Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 17

FASTRAK MANUAL

Rev. G

12

JUNE 2012

6. Specification

Position Coverage

The system will provide the specified accuracy when standard* receivers are located within 30 inches (76
cm.) of the standard transmitter. Operation with separations up to 120 inches (305 cm.) is possible with
reduced accuracy.

*NOTE:

Alternative devices of larger/smaller size are available as options and operate to longer/shorter

ranges.

Angular Coverage

The receivers are all-attitude.

Static Accuracy

0.03” (0.08 cm) RMS for the X,Y,or Z receiver position, and 0.15

°

RMS for receiver orientation.

Resolution vs. Range

Latency

4.0 milliseconds from center of receiver measurement period to beginning of transfer from output port.

Output

Software selectable including extended precision. Cartesian coordinates of position and Euler orientation
angles are standard. Direction cosines and quaternions are selectable. English or metric units and ASCII
or binary outputs also are selectable.

Update Rate

One receiver

120 updates/second

Two receivers

60 updates/second

«
...
15
16
17
18
19
...
»

Содержание 3SPACE FASTRAK





























































































































Отзывы:

Нет отзывов