Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 124

Polhemus 3SPACE FASTRAK Скачать руководство пользователя страница 106

FASTRAK MANUAL

Rev. G

C-8

JUNE 2012

User Defaults

The values assigned to certain system variables by the user. Stored in
EEPROM, the system receives these variable values at power-up.

XYZ or X,Y,Z

The Cartesian coordinates of position tracking where noX is in
the forward direction; +Y is in the right hand direction and +Z is upward.

XYZAER

The output string of date reporting the position, XYZ, and orientation,
AER - azimuth, elevation and roll, of the tracking receiver.

Yaw

Same as azimuth.

<>

Used in text to indicate the “Enter” key.

...

An ellipsis indicates that you can repeat an item.

,

A comma represents a delimiter in a list of optional parameters. The
comma must be present for those parameters which are omitted except for
the case of trailing commas. For example:

Qs,p1,,,p4<>

is the proper command format when omitting parameters p2 and p3.
Commas following the parameter p4 are not required if parameters p5 and
p6 are omitted.

|

A vertical bar means either/or. Choose one of the separated items and type
it as part of the command. For example,

ON|OFF

indicates that you should enter either ON or OFF, but not both.

Do not

enter the vertical bar.

^

Used in text to indicate the “Ctrl” key.

«
...
104
105
106
107
108
...
»

Содержание 3SPACE FASTRAK





























































































































Отзывы:

Нет отзывов