manualshive.com logo in svg

PI E-871.1A1N, Руководство пользователя, Страница: 11 / 226

Поделиться
Скачать
PI E-871.1A1N Скачать руководство пользователя страница 11

3

Safety

3.1

Intended Use

The E-871.1A1N is a laboratory device as defined by DIN EN 61010-1. It is intended for indoor
use and use in an environment that is free of dirt, oil, and lubricants.
In accordance with its design, the E-871.1A1N is intended to operate PI positioners that are
equipped with piezo inertia drives (Q-Motion®,PiezoMike). The E-871.1A1N is intended for
closed-loop operation with incremental position sensors. In addition, it can read and process
the reference point and limit switch signals from the connected positioner.
The E-871.1A1N may not be used for purposes other than those stated in this user manual. In
particular, the E-871.1A1N may not be used to drive ohmic or inductive loads.

3.2

General Safety Instructions

The E-871.1A1N is built according to state-of-the-art technology and recognized safety
standards. Improper use of the E-871.1A1N may result in personal injury and/or damage to
the E-871.1A1N.

►

Use the E-871.1A1N only for its intended purpose and if it is in perfect condition.

►

Read the user manual.

►

Eliminate any faults and malfunctions that are likely to affect safety immediately.

The operator is responsible for correct installation and operation of the E-871.1A1N.

►

Install the E-871.1A1N near the power adapter so that the power plug can be quickly and
easily disconnected from the mains.

►

Use the components supplied to connect the E-871.1A1N to the power supply.

►

If one of the supplied components for connecting to the power supply has to be replaced,
use a sufficiently dimensioned component.

►

Only use cables and connections that comply with local safety regulations.

3.3

Organizational Measures

3.3.1

User Manual

►

Always keep this user manual available with the E-871.1A1N. The latest versions of the
user manuals can be 

downloaded (p. 10)

 at 

www.pi.ws

.

►

Add all information from the manufacturer such as supplements or technical notes to the
user manual.

►

If you give the E-871.1A1N to a third party, also include this user manual as well as other
relevant information provided by the manufacturer.

►

Only use the device on the basis of the complete user manual. Missing information due to
an incomplete user manual can result in minor injury and damage to equipment.

►

Only install and operate the E-871.1A1N after you have read and understood this user
manual.

3.3.2

General Personnel Qualification

The E-871.1A1N may only be installed, started up, operated, maintained, and cleaned by
authorized and appropriately qualified personnel.

3  SAFETY

PZ285EN 

‒

 1/30/2019

11

M O T I O N   |   P O S I T I O N I N G

Содержание E-871.1A1N



































































































































































































































Отзывы:

Нет отзывов