Panasonic EverVolt EVAC-105-6 Скачать руководство пользователя страница 7

Страница: 7 / 99

Installation Manual

Important Safety Warnings

IMPORTANT SAFETY WARNINGS

PLEASE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS ON

THE UNIT AND THIS MANUAL BEFORE USING THE INVERTER. AND,

STORE THIS USER MANUAL WHERE IT CAN BE ACCESSED EASILY.

WARNING: Users and homeowners should not attempt to service

Evervolt. Only an authorized Panasonic technician should attempt to
service EverVolt.

Safety Symbols

WARNING:

This indicates the risk of electric shock. The

presence of high voltage levels may constitute a risk of injury

or death to users and/or installers.

CAUTION:

This indicates important information where failure

to comply may result in safety hazards or cause damage to

this product.

CAUTION:

This indicates the risk of a hot surface. The

surface may reach a temperature high enough to cause

serious burn injuries.

General Precautions

CAUTION:

Before installing and using this inverter, read all

instructions and cautionary markings on the inverter and

all appropriate sections of this guide. This inverter must be

installed by licensed electricians only.

CAUTION:

Normally grounded conductors may be

ungrounded and energized when a ground fault is

indicated.

CAUTION:

This inverter is heavy. It should be lifted by at least

two persons for safety.

WARNING:

These servicing instructions are for use by

qualified personnel only. To reduce the risk of electric shock,

do not perform any servicing other than that specified in the

operating instructions unless you are qualified to do so.

Содержание EverVolt EVAC-105-6




































































































Результаты поиска

Содержание EverVolt EVAC-105-6

Отзывы:

Похожие инструкции для EverVolt EVAC-105-6

Бренды по названию

Популярные бренды

Panasonic EverVolt EVAC-105-6, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EverVolt EVAC-105-6

Отзывы:

Похожие инструкции для EverVolt EVAC-105-6

Бренды по названию

Популярные бренды