Panasonic EverVolt EVAC-105-6 Скачать руководство пользователя страница 12

Страница: 12 / 99

Installation Manual

Important Safety Warnings

INVERTER WARNINGS:

The inverter is intended to operate

with an internet connection. Failure to maintain an internet

connection may have an impact on the warranty.

Properly mount the Inverter or place it on a flat, plain surface

that can bear heavy weights. Ensure that the mounting

location is structurally suited to bearing the weight of the

Inverter.

During use, storage, and transport, keep the inverter:

• Properly ventilated

• Away from water, other liquids, heat, sparks, and direct

sunlight

• Away from excessive dust, corrosive and explosive gases,

and oil smoke

• Away from direct exposure to gas exhaust, such as from

motor vehicles

• Free of vibrations

• Away from falling or moving objects, including motor

vehicles

• At an elevation of less than 3,000m (9843ft) above

sea-level

• In a location compliant with fire safety regulations (has a

smoke alarm)

• In a location compliant with local building codes and

standards

• Conditions for the inverter installation site apply also to

storage conditions.

Содержание EverVolt EVAC-105-6




































































































Результаты поиска

Содержание EverVolt EVAC-105-6

Отзывы:

Похожие инструкции для EverVolt EVAC-105-6

Бренды по названию

Популярные бренды

Panasonic EverVolt EVAC-105-6, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EverVolt EVAC-105-6

Отзывы:

Похожие инструкции для EverVolt EVAC-105-6

Бренды по названию

Популярные бренды