Panasonic EverVolt EVAC-105-6 Скачать руководство пользователя страница 68

Страница: 68 / 99

Installation Manual

Step 2. Use the <-- or --> keys to toggle between modes and

to select

it.

Step 3. For modes “Time of Use” or “Time of Use with Battery Feed-in

(Grid Export)”, enter the start/end times for “High Price Duration” in 24-

hour notation. Use the <-- or --> keys to change the number, and then

to set it. Once the value for the last time field is set, press the

key.

Operation and Display Panel

Step 4. Settings are being updated. Please wait for next message.

Step 5. Press any key and manually restart with the main switch located

on the left side of the inverter. If you get a setting fail message, press any

key. Please re-turn on the main switch and re-setting the mode again. If

still get a setting fail message, please contact Panasonic.

Содержание EverVolt EVAC-105-6




































































































Результаты поиска

Содержание EverVolt EVAC-105-6

Отзывы:

Похожие инструкции для EverVolt EVAC-105-6

Бренды по названию

Популярные бренды

Panasonic EverVolt EVAC-105-6, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EverVolt EVAC-105-6

Отзывы:

Похожие инструкции для EverVolt EVAC-105-6

Бренды по названию

Популярные бренды