Panasonic EverVolt EVAC-105-6 Скачать руководство пользователя страница 9

Страница: 9 / 99

Installation Manual

Important Safety Warnings

BATTERY PACK WARNINGS:

There is danger of generating heat / smoke / rupture flames.

Do not disassemble battery pack.

Do not touch disassembled battery pack.

Do not reassemble battery pack.

Do not immerse the battery pack in any liquids or get it wet.

Do not short circuit battery pack.

Do not incinerate or heat the battery pack.

Do not use or leave the battery near a fire, stove or heated

place.

Do not impact the battery pack or throw it.

Do not use a damaged and/or deformed battery pack.

Do not drive sharp objects into the battery pack, strike it with

any object or stand on it.

Do not place the battery pack on materials such as tools,

electric wire, screws, etc.

In case of a leak in the battery pack, avoid contact.

Do not touch your eyes if accidental contact with leaky

battery.

Do not expose to corrosive substances such as sea breeze,

steam or chemicals.

Do not install in humid places or places with condensation.

Do not install or use EverVolt if it has been damaged in any

way.

Содержание EverVolt EVAC-105-6




































































































Результаты поиска

Содержание EverVolt EVAC-105-6

Отзывы:

Похожие инструкции для EverVolt EVAC-105-6

Бренды по названию

Популярные бренды

Panasonic EverVolt EVAC-105-6, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EverVolt EVAC-105-6

Отзывы:

Похожие инструкции для EverVolt EVAC-105-6

Бренды по названию

Популярные бренды