55
Chapter 6
W
elding Condition
&KDSWHU:HOGLQJ&RQGLWLRQ
This chapter explains the functions on the operation panel as well as how to set the welding conditions.
/LVWRI:HOGLQJ&RQGLWLRQV
This section explains the parameters/functions settable in the welding power source.
3DUDPHWHU:HOGLQJSDUDPHWHU
)XQFWLRQ
Parameter
Set Range
Initial Value
Descriptions
Pre-flow time
0 to 10 sec
0.1 sec
Set the gas discharge time before welding starts.
Initialized condition/
Main condition/
Crater condition
Current
WB-M352
Three phase:
20 to 400 A
10 to 400 A
(for DC TIG welding)
20 to 300 A
(for DC STICK welding)
150 A
100 A (initial/
crater)
Initial Condition: set the current and voltage value
soon after the welding.
Welding condition: set the current and voltage value
during the welding.
Crater condition: set the current and voltage value at
the end of welding.
Single phase:
20 to 250 A
10 to 250 A
(for DC TIG welding)
20 to 250 A
(for DC STICK welding)
WB-M502
20 to 550 A
10 to 400 A
(for DC TIG welding)
20 to 400 A
(for DC STICK welding)
Voltage
(INDIVIDUAL)
(*1)
WB-M352
Three phase:
12.0 to 38.0 V
23.5 V
21.5 V (initial/
crater)
Single phase:
12.0 to 34.0 V
WB-M502
12.0 to 50.0 V
Voltage
(SYNERGY)
(*1)
-100 to 100
0
Post-flow time
0 to 10 sec
0.4 sec
Set the gas discharge time after the welding ends.
Arc spot time
0.1 to 10 sec
3 sec
Set the welding time at arc spot.
Arc characteristics
-10 to 10
0
Set the arc to the condition from soft to hard.
Welding condition memory No.
1 to 100
1
Register the welding conditions (storable up to 100).
*1: There is no voltage adjustment for DC TIG welding and DC STICK welding.
Function
Initial value
Setting parameter
CRATER-FILL
CRATER-FILL-OFF
CRATER-FILL-OFF/CRATER-FILL-ON/CRATER-FILL-ON (Repeat)/ARC SPOT
GAS
MAG (20% CO
2
)
CO
2
/MAG (20% CO
2
) / MIG (2% O
2
) / MIG (100% Ar)
WIRE MATERIALS
MILD STEEL
MILD STEEL/MILD STEEL CORED/METAL CORED/STAINLESS CORED/STAINLESS STEEL/
STAINLESS FERRITE/SOFT ALUMINUM/HARD ALUMINUM
WELDING METHOD
DC
DC/DC TIG/DC STICK
WIRE DIA.
[in. (mm)]
.045 (1.2)
WB-M352
.030 / .035 / .040 / .045 / .052 / 1/16 (0.8/0.9/1.0/1.2/1.4/1.6)
WB-M502
.035 / .040 / .045 / .052 / 1/16 (0.9/1.0/1.2/1.4/1.6)
INITIAL CONDITION
OFF
ON/OFF
VOLT. ADJUST
INDIV.
SYNERG. /INDIV.
CONSTANT
PENETRATION
OFF
ON/OFF
Содержание Welbee M350 II
