111
Chapter 7
Administrator F
unctions
D
ATA
B
ACKUP
(U
TILIZATION
OF
DATA
)
A
DMINISTRATOR
F
UNCTIONS
C
HAPTER
7
The current welding conditions set with the operation panel will not be saved. (If necessar , record them in memor beforehand.)
The welding condition data recorded in the memor will be output in the wa that the JOB Nos. (registration Nos.) are
displa ed in a vertical line and the parameter values in a hori ontall line.
Item
Description
Unit Item
Description
Unit
job_num
JOB No.
1 to 100
wmode_H
Process information 1
(*2)
spot_tim
Arc Spot time
0.1 (s)
wmode_L
Process information 2
(*2)
prf_tim
Pre-flow time
0.1 (s)
reserve
Reserved
-
pre_iset
Initial current
1 (A)
reserve
Reserved
-
pre_vset
Initial voltage
0.1 (V)
reserve
Reserved
-
pre_uni_vset
Initial voltage (synergic)
1 (±)
ant_tim_adj
Anti-stick time adjustment
0.01 (s)
wld_iset
Welding current
1 (A)
ant_vset_adj
Anti-stick voltage
adjustment
0.1 (V)
wld_vset
Welding voltage
0.1 (V)
sldwn_adj
Slowdown adjustment
3.9 (IPM)
[0.1 (m/min)]
wld_uni_vset
Welding voltage (synergic)
1 (±)
up_slp_tim
Up-slope time
0.1 (s)
cre_iset
Crater current
1 (A)
dwn_slp_tim
Down-slope time
0.1 (s)
cre_vset
Crater voltage
0.1 (V)
pre_tim
Initial time
0.1 (s)
cre_uni_vset
Crater voltage
(synergic)
1 (±)
cre_tim
Crater time
0.1 (s)
aff_tim
Post-flow time
0.1 (s)
PerIset
Setting change of current
value
0/1 (OFF/ON)
arc_char
Arc characteristics
1 (±)
PreIsetPer
Setting of current value
(initial condition)
1 (%)
arc_char2
Arc characteristics
(reserved)
−
CreIsetPer
Setting of current value
(crater condition)
1 (%)
pre_sens_cnst
−
−
TsCrickIset
Torch switch
current adjustment
0/1 (OFF/ON)
reserve
Reserved
−
CriIsetStep1
Current increase/decrease
value by single clicking
1 (A)
reserve
Reserved
−
CriIsetStep2
Current increase/decrease
value by double clicking
1 (A)
reserve
Reserved
−
reserve
Reserved
−
pre_feed
Initial feeding speed
3.9 (IPM)
[0.1 (m/min)]
Interval
Interval welding
0/1 (OFF/ON)
wld_feed
Welding feeding speed
3.9 (IPM)
[0.1 (m/min)]
Interval_ON
Arc-ON time on interval
welding
0.01 (s)
cre_feed
Crater feeding speed
3.9 (IPM)
[0.1 (m/min)]
Interval_OFF
Arc-OFF time on interval
welding
0.01 (s)
reserve
Reserved
−
exp_ctrl
Extended control
information
−
reserve
Reserved
−
dummy1 to 10
Reserved
−
ctrl
Sequence information
(*1)
chksum
Checksum
Checksum
data
*1: Crater sequence and other information is recorded.
*2: Wire diameter, material, shield gas and other process information is recorded.
"-" is shown for unused condition numbers.
Parameter of condition No.1
Parameter value
JOB No.
Содержание Welbee M350 II
