manualshive.com logo in svg

Omron GX-AD0471, Руководство пользователя, Страница: 91 / 394

Поделиться
Скачать
Omron GX-AD0471 Скачать руководство пользователя страница 91

6 - 7

6   Basic Specifications of Slave Units

GX-series EtherCAT Slave Unit User’s Manual

6-3  Sp

ecificat

ion
s of

 Com

m

o

n

 Area

s

6

6-

3-2  Nod

e 

Addr

ess Setting Switches

The node address setting switches are used to set node address of the Slave Unit in the EtherCAT 
network as a hexadecimal value.
Set the hexadecimal value of the EtherCAT node address of the IO-Link Master Unit on the rotary 
switches in the following order starting from the rightmost switch: rightmost digit (x1), middle digit (x16), 
and leftmost digit (x256).
The setting range is from 000 to FFF hex (0 to 4,095 decimal). (Default setting: 000)

The valid node address set value varies as shown below when the EtherCAT Master Unit is made by 
OMRON or by another manufacturer.

Precautions for Correct Use

•

The setting on the node address switches is read only once when the power is turned ON. If
the setting is changed after turning ON the power supply, it is not reflected in control. It
becomes effective the next time the power supply is turned ON.

•

If the same node address is allocated to more than one node, an error occurs and operation
stops (for an OMRON EtherCAT Master Unit).

•

If you set the node address switches to 000, the Slave Unit will not operate if the node address
setting made from the Configuration Tool is not changed from 000 to another value. If the node
address switches are set to 000, always use the Configuration Tool to change the node
address to a value between 1 and 65,535. (This applies when an OMRON NJ/NX-series
EtherCAT Master Unit is used. If a master manufactured by another company is used, the set
value can be used as an ID.)

IO-Link Master Unit

Node address 
switch setting

Valid set value for node address

OMRON EtherCAT Master Unit

EtherCAT Master Unit from another 

manufacturer

000

Value set with Configuration Tool (Default 
setting: 0, Setting range: 1 to 65,535)

Value set with Configuration Tool (The 
setting on these switches is ignored.)

001 to FFF

Setting on node address switches on the 
Unit

GX-ILM08C

01234

56789

ABC

DE

F

01234

56789

ABC

DE

F

01234

56789

ABC

DE

F

Node address setting, ×1

Node address setting, ×16

Node address setting, ×256

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов