manualshive.com logo in svg

Omron GX-AD0471, Руководство пользователя, Страница: 61 / 394

Поделиться
Скачать
Omron GX-AD0471 Скачать руководство пользователя страница 61

4 - 13

4   Installation and Wiring

GX-series EtherCAT Slave Unit User’s Manual

4-4
  Con

n

ect
ing
 an Ext

er

n

al Dev

ice

4

4-

4-1  C

onnecting to

 a Scr

ew 
Ter

m

ina
l Block

4-4

Connecting an External Device

Connect an external device to the I/O terminal of a Slave Unit.
The method of connection differs between Units with screw terminal blocks and Units with e-CON 
connectors.

After mounting a crimp terminal to the cable of the external device to be connected, connect it to the 
terminal block.

1

Mount the following crimp terminal to the signal line of the cable.

2

Connect the signal line to the terminal block.

Tighten the terminal block screws to the appropriate tightening torque of 0.5 N • m.
The terminal block is removable; remove the left and right screws if it is necessary to remove 
the terminal block to connect the signal line.

Precautions for Correct Use

To remove the terminal block from the Slave Unit, loosen the left and right mounting screws 
alternately. When mounting the terminal block as well, tighten the left and right screws 
alternately.
If you tighten or loosen only one of the screws all the way without tightening or loosening the 
other screw using an electric screwdriver, the terminal block will be distorted and cracked.

4-4-1

Connecting to a Screw Terminal Block

6.0 mm max.

6.0 mm max.

φ3.2 mm min.

3.2 mm min.

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов