Omron GX-AD0471 Скачать руководство пользователя страница 239

Страница: 239 / 394

10 - 3

10 IO-Link Master Unit

GX-series EtherCAT Slave Unit User’s Manual

10-
1 What

Is an IO-L

ink Ma

ster

Un
it?

10
-1-3

S
u

pport Softw

are to Be U

sed

The following support software tools are used for IO-Link Systems.

For the versions of the Sysmac Studio and CX-ConfiguratorFDT that are compatible with the IO-Link
Master Unit, refer to

A-7 Version Information

on page A-83.

10-1-3 Support Software to Be Used

Controller

Application

I/O allocation setting

for controller

PDO assignment

setting

IO-Link master

setting

Settings/monitor for

I/O-Link device

NJ/NX-series
CPU Unit

Sysmac Studio

CX-ConfiguratorFDT

NY-series
Industrial PC
Controllers from
other
manufacturers

EtherCAT configuration
tool from other
manufacturers

EtherCAT
configuration tool
from other
manufacturers

Configured via
message
communications from
a master
manufactured by
other manufacturers

Содержание GX-AD0471











































































































































































































































































































































































































Результаты поиска

Содержание GX-AD0471

Отзывы:

Omron GX-AD0471, Руководство пользователя, Страница: 239 / 394

Результаты поиска

Содержание GX-AD0471

Отзывы: