manualshive.com logo in svg

Omron GX-AD0471, Руководство пользователя, Страница: 199 / 394

Поделиться
Скачать
Omron GX-AD0471 Скачать руководство пользователя страница 199

8 - 21

8   Analog I/O Slave Unit

GX-series EtherCAT Slave Unit User’s Manual

8-

6  Overview 

of Each

 Slave Un

it T
ype

8

8-6-

1  4-

point I

nput Slave Un

it GX-AD04

71

•

Input range setting switches

Set input range by combination of individual DIP switches.
To enable settings of these switches, it is necessary to turn Pin8 (input range setting method) ON in 
advance.

Precautions for Correct Use

•

When setting a range with these switches, the same input ranges are set for inputs CH1 and 
CH2 as well as inputs CH3 and CH4, respectively. To set a different range for inputs CH1 to 
CH4, use the SDO communications to make the settings.

•

Pin7 must be used in the OFF state.

•

To set a range using these switches, make sure to turn Pin8 ON. If it is turned OFF, the DIP 
switch settings will not be reflected.

•

The settings of this switch are read only once when the power is turned ON.

•

Setting of input CH1/CH2 range (Pin1 to Pin3)

•

Setting of input CH3/CH4 range (Pin4 to Pin6)

Precautions for Correct Use

Do not set the DIP switches or Pins other than as specified in the tables above.

Pin No.

Setting

Specification

1

Setting of input CH1/CH2 range (common)

Set by combination of DIP switches (see the 
next table)

2
3
4

Setting of input CH3/CH4 range (common)

5
6

7

Always OFF

Make sure to keep it OFF.
The operation cannot be guaranteed when it is 
set to ON.

8

Input range setting method

OFF: Setting by SDO communications
ON: Setting by the switches (Pin1 to Pin6)

Input range

Pin1

Pin2

Pin3

0 to 5 V

OFF

OFF

OFF

1 to 5 V

ON

OFF

OFF

0 to 10 V

OFF

ON

OFF

−

10 to +10 V

ON

ON

OFF

4 to 20 mA

OFF

OFF

ON

Input range

Pin4

Pin5

Pin6

0 to 5 V

OFF

OFF

OFF

1 to 5 V

ON

OFF

OFF

0 to 10 V

OFF

ON

OFF

−

10 to +10 V

ON

ON

OFF

4 to 20 mA

OFF

OFF

ON

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов