manualshive.com logo in svg

Omron GX-AD0471, Руководство пользователя, Страница: 304 / 394

Поделиться
Скачать
Omron GX-AD0471 Скачать руководство пользователя страница 304

12   Troubleshooting and Maintenance

12 - 24

GX-series EtherCAT Slave Unit User’s Manual

Periodically inspect the following items to ensure that they do not deviate from the criteria.
If the items deviate from the criteria, adjust the environment so the criteria are met or adjust the Unit 
itself.

Networks are constructed from an EtherCAT Master Unit and Slave Units. 
If a Unit is malfunctioning, the entire network will be affected. The malfunctioning Unit must be replaced 
quickly.
To restore network functions as quickly as possible, it is recommended that spare Units are kept on 
hand ready to replace malfunctioning Units immediately.

Heed the following precautions when replacing nodes after a periodic inspection has revealed a 
problem.

•

Check that the new Unit does not have errors after replacement.

•

If returning malfunctioning devices for repair, attach a detailed description of the malfunction to the 
device and send the device to the OMRON representative listed at the end of this manual or to your 
OMRON representative.

•

If contacts are defective, wipe them with a clean pure cotton cloth that has been soaked in industrial 
alcohol.

After replacing a Unit, make the switch and other settings the same as before the Unit was replaced.

Refer to the 

IO-Link System User’s Manual

 (W570) for information on replacing an IO-Link Master Unit.

Inspection item

Inspection 

item

Inspection details

Criteria

Inspection 

method

Environment

Are the ambient and in-panel 
temperatures appropriate?

−

10 to 55

°

C

Thermometer

Is the ambient and in-panel humidity 
appropriate?

25 to 85% (with no 
condensation)

Hygrometer

Has dust collected?

No dust

Visual inspection

Installation

Has the Slave Unit been secured?

No looseness

Phillips screwdriver

Are the communications cable 
connectors inserted properly?

No looseness

Visual inspection

Are the external wiring screws loose?

No looseness

Phillips screwdriver

Are the connection cables damaged?

No visible damage

Visual inspection

12-2-3 Handling when Replacing Units

Precautions when replacing Units

Settings after Unit replacement

12-2-4 Replacing the IO-Link Master Unit or IO-Link Devices

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов