manualshive.com logo in svg

Omron GX-AD0471, Руководство пользователя, Страница: 44 / 394

Поделиться
Скачать
Omron GX-AD0471 Скачать руководство пользователя страница 44

3   Basic Usage Procedures

3 - 2

GX-series EtherCAT Slave Unit User’s Manual

3-1

Setup Examples and Basic 

Procedure

This section explains the setup method by using simple system setting examples.

Connect each of the following Slave Units to the EtherCAT Master Unit and make the settings. 

Although it is not shown in the figure above, supply the unit power and the I/O power separately. 

3-1-1

System Setting Examples

Digital I/O Slave Unit
GX-ID1611 (16 inputs)
              +
Expansion Unit
XWT-ID16 (16 inputs)

Set the node address to 1.

Digital I/O Slave Unit
GX-OD1611 (16 outputs)
              +
Expansion Unit
XWT-OD16 (16 outputs)

Set the node address to 2.

Analog I/O Slave Unit
GX-AD0471 (4 inputs)

Set the node address to 5.

Encoder Input Slave 
GX-EC0211 (2 inputs)

Set the node address to 6.

IO-Link Master Unit
GX-ILM08C

Set the node address to 7.

EtherCAT Master Unit

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов