manualshive.com logo in svg

Omron GX-AD0471, Руководство пользователя, Страница: 50 / 394

Поделиться
Скачать
Omron GX-AD0471 Скачать руководство пользователя страница 50

4   Installation and Wiring

4 - 2

GX-series EtherCAT Slave Unit User’s Manual

4-1

Mounting Slave Units

This section describes the DIN Track mounting method for GX-series Digital I/O Slave Units, Analog I/O 
Slave Units, and Encoder Input Slave Units.

Prepare the following devices.

There are no restrictions in the orientation unless otherwise specified in the instruction pages for the 
Slave Unit. 
Mounting is possible in any of the following 6 orientations.

1

Hook the top side of groove on backside of the Slave Unit  to the top side of the DIN 
track, lower the DIN track mounting hook, engage the Slave Unit to the track, and press 
up the mounting hook to fix it.

4-1-1

Mounting Preparation

Product name

Model

Comment

35-mm DIN track

PFP-50N

Length 50 cm

PFP-100N

Length 100 cm

PFP-100N2

Length 100 cm

End plate

PFP-M

2 end plates are required for each Slave Unit.

4-1-2

Mounting Direction

4-1-3

Mounting Method

Vertical direction

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов