Omron GX-AD0471 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 394

Omron GX-AD0471 Скачать руководство пользователя страница 51

4 - 3

4 Installation and Wiring

GX-series EtherCAT Slave Unit User’s Manual

4-

1 Mou

n

tin
g

Slave

Unit

s

4

4-

1-4 R

emoval Method

2

Hook the bottom side of the end plate to the bottom side of the DIN track and then hook
the top side.
Attach an end plate on each side of the Unit.

Precautions for Safe Use

After the operation, make sure to check that the Slave Unit is securely mounted.

Loosen the screws on the end plate and remove the end plate from the DIN track. Then pull down the
DIN track mounting hook to release the lock. Pull out the Slave Unit straight toward you.

4-1-4

Removal Method

DIN track

DIN track mounting hook

(2)

(1)

End plate

(2)

(1)

«
...
49
50
51
52
53
...
»

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов