manualshive.com logo in svg

Omron GX-AD0471, Руководство пользователя, Страница: 244 / 394

Поделиться
Скачать
Omron GX-AD0471 Скачать руководство пользователя страница 244

10   IO-Link Master Unit

10 - 8

GX-series EtherCAT Slave Unit User’s Manual

Load rejection for controller 
communications error

This function turns OFF outputs from the IO-Link Master Unit when an 
error occurs in communications with the controller in IO-Link Mode or in 
an SIO mode.
This prevents output operations with incorrect values when a 
communications error occurs.

IO-Link total communications lost 
frames

The IO-Link total communications lost frames can be read from the 
CX-ConfiguratorFDT.
You can use this function to determine communications status as 
affected by IO-Link communications noise or other factors.

Digital input filter

You can remove the chattering and noise of the input signal for digital 
inputs in SIO (DI) Mode or for digital inputs for pin 2 in IO-Link Mode.
When the input data changes without stabilization of the state of the 
contact point due to chattering and noise, this function prevents 
changes in data and stabilizes it.

Digital input collection
(Unit version 1.1 or later)

In IO-Link Mode, this function reflects the specified bit data in the input 
data from the IO-Link device on the digital input data of the IO-Link 
Master Unit. As a result, the bit data in the input data from the IO-Link 
device can be aggregated into the digital input data of the IO-Link 
Master Unit. One bit for each IO-Link port can be aggregated. This 
function cannot be used in SIO (DI) Mode and SIO (DO) Mode.
If you are using this function, you cannot perform digital inputs for pin 2.

Backup and restoration of parameter 
settings in IO-Link devices

This function is used to back up parameter settings in IO-Link devices in 
the IO-Link Master Unit or restore them to IO-Link devices.
This eliminates the need to set parameters again after replacing an 
IO-Link device.

Event log

This function records events, such as errors and status changes, that 
occur in the IO-Link Master Unit and IO-Link devices.

Function name

Description

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов