manualshive.com logo in svg

Omron GX-AD0471, Руководство пользователя, Страница: 290 / 394

Поделиться
Скачать
Omron GX-AD0471 Скачать руководство пользователя страница 290

12   Troubleshooting and Maintenance

12 - 10

GX-series EtherCAT Slave Unit User’s Manual

Analog input Slave Unit

The disconnection 
indication does not clear.

The sensor is 
disconnected.

Restore the sensor 
connection.
Check the connected 
sensor and input type.

Disconnection is not 
detected.

Disconnection can not be 
detected for ranges other 
than 1 to 5 V and 4 to 20 
mA.

Check that the input range 
is correct.

A disconnection is 
detected even though it is 
not disconnected.

The connected sensor 
does not conform to the 
input range set on the 
Unit.

Check the type of 
connected sensor and the  
range setting on the Slave 
Unit again.

The user adjustment error 
is too large.

Execute user adjustment 
again.

The conversion cycle is 
too long.

The number of AD 
conversion points is set to 
maximum (4 points). 

Reduce the number of 
points if some inputs are 
unnecessary, and execute 
conversion again.

User adjustment is not 
accepted.

Attempted to make 
adjustment with inputs 
outside the compensation 
range.

Enter a voltage (current) 
within the compensation 
range with the input 
device and make 
adjustment again.
If a voltage (current) within 
the compensation range 
cannot be entered, check 
the method being used to 
connect the input device.

Analog output Slave Unit

Cannot hold expected 
outputs when 
communications errors 
occur.

The output value that is 
set for communications 
errors is incorrect.

Change the setting to hold 
outputs for 
communications errors.

The conversion cycle is 
too long.

The number of DA 
conversion points is set to 
maximum (2 points). 

Reduce the number of 
points if some outputs are 
unnecessary, and execute 
conversion again.

User adjustment is not 
accepted.

Attempted to make 
adjustment with values 
outside the compensation 
range.

Use a voltage (current) 
within the setting range to 
make adjustment again.
If the final output cannot 
be adjusted within the 
correctable range, check 
the method being used to 
connect to the output 
device.

Slave Unit type

Symptom

Cause

Measures

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов