manualshive.com logo in svg

Omron GX-AD0471, Руководство пользователя, Страница: 385 / 394

Поделиться
Скачать
Omron GX-AD0471 Скачать руководство пользователя страница 385

A - 81

A   Appendix

GX-series EtherCAT Slave Unit User’s Manual

A-6  Glo

ssary

A

A-6 Glossary

Use the following list of EtherCAT terms for reference.

Term

Abbrevia-

tion

Description

AL status (application layer status)

−

Status for indicating information on errors that occur in an application 
on a slave.

cable redundancy

−

A function for continuing the communications even when cable 
disconnection or slave power failure occurs on the EtherCAT system.

CAN application protocol over 
EtherCAT

CoE

A CAN application protocol service implemented on EtherCAT.

CAN in Automation

CiA

CiA is the international users' and manufacturers' group that 
develops and supports higher-layer protocols.

device profile

−

Collection of device dependent information and functionality 
providing consistency between similar devices of the same device 
type.

distributed clocks

DC

Clock distribution mechanism used to synchronize EtherCAT Slave 
Units and the EtherCAT Master Units.

EtherCAT slave controller

ESC

A controller for EtherCAT slave communication.

EtherCAT slave information

ESI

An XML file that contains setting information for an EtherCAT Slave 
Unit.

EtherCAT state machine

ESM

An EtherCAT communication state machine.

EtherCAT Technology Group

ETG

The ETG is a global organization in which OEM, End Users and 
Technology Providers join forces to support and promote the further 
technology development.

index

−

Address of an object within an application process.

network configuration information

−

The EtherCAT network configuration information held by the 
EtherCAT master.

object

−

Abstract representation of a particular component within a device, 
which consists of data, parameters, and methods.

object dictionary

OD

Data structure addressed by Index and Sub-index that contains 
description of data type objects, communication objects and 
application objects.

operational

−

A state in EtherCAT communications where SDO communications 
and I/O are possible.

PDO communications

−

An acronym for process data communications.

pre-operational

−

A state in EtherCAT communications where only SDO 
communications are possible without being able to perform I/O.

Process data

−

Collection of application objects designated to be downloaded 
cyclically or acyclically for the purpose of measurement and control.

process data communications

−

One type of EtherCAT communications that uses process data 
objects (PDOs) to exchange information in realtime with a fixed 
cycle. This is also called PDO communications.

Process data object

PDO

Structure described by mapping parameters containing one or 
several process data entities.

Receive PDO

RxPDO

A process data object received by an EtherCAT Slave Unit.

safe operational

−

A state in EtherCAT communications where only SDO 
communications and reading input data from slaves are possible. 
Outputs from slaves are not performed.

SDO communications

−

One type of EtherCAT communications that uses service data 
objects (SDOs) for communicating information when required.

service data object

SDO

CoE asynchronous mailbox communications where all objects in the 
object dictionary can be read and written. 

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов