manualshive.com logo in svg

Omron GX-AD0471, Руководство пользователя, Страница: 336 / 394

Поделиться
Скачать
Omron GX-AD0471 Скачать руководство пользователя страница 336

A   Appendix

A - 32

GX-series EtherCAT Slave Unit User’s Manual

This section explains the CiA401 generic I/O module device profile implemented in GX-series 
EtherCAT Slave Units and the objects specially mounted in GX-series EtherCAT Slave Units. 

Manufacturer Specific area 1

•

This object clears diagnosis history of 10F3 hex (Diagnosis History).

•

It clears the history only when specific values are written. The specific value is "elcl". 

Writing values other than this is invalid.

•

The mapping is used for Sysmac error status notification and to clear Sysmac error status.

•

Sub-index 1: Sysmac Error Status

•

This object is for notification of errors that are detected in the Slave Unit.

•

When connected to an NJ-series Machine Automation Controller (NJ501-1

@

00), map this object 

to a PDO.

•

Sub-index 2: Sysmac Error Status Clear

•

This object is used by the Controller (a Sysmac device) to reset errors that occur in Slave Units.

•

For the GX-series Digital I/O Slave Units, Analog I/O Slave Units, and Encoder Input Slave Units, this 
object can be set for unit version 1.1 or later.

•

For the GX-series IO-Link Master Unit, this object can be set for unit version 1.0 or later.

Reference

In the default Sysmac Studio settings, sub-index 1 (Sysmac Error Status) is automatically 
mapped to a PDO because 1BFF hex (512th transmit PDO Mapping) is assigned.

A-1-7

Manufacturer Specific Objects

All Slave Units

2100 hex

Error History Clear

Range: 

−

Unit: 

−

Default: 00000000 hex

Attribute: A

Size: 4 bytes (U32)

Access: RW

PDO map: Not possible

MSB

LSB

l

c

l

e

6C hex

63 hex

6C hex

65 hex

2002 hex

Sysmac Error

Sub-index 0: Number of entries
Range: 

−

Unit: 

−

Default: 02 hex

Attribute: 

−

Size: 1 byte (U8)

Access: RO

PDO map: Not possible

Sub-index 1: Sysmac Error Status
Range: 

−

Unit: 

−

Default: 00 hex

Attribute: 

−

Size: 1 byte (U8)

Access: RO

PDO map: Possible

Sub-index 2: Sysmac Error Status Clear
Range: 

−

Unit: 

−

Default: 00 hex

Attribute: A

Size: 1 byte (U8)

Access: RW

PDO map: Not possible

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов