manualshive.com logo in svg

Omron GX-AD0471, Руководство пользователя, Страница: 212 / 394

Поделиться
Скачать
Omron GX-AD0471 Скачать руководство пользователя страница 212

9   Encoder Input Slave Unit

9 - 6

GX-series EtherCAT Slave Unit User’s Manual

Abbreviations used for the counter status information description have the following meanings.

Encoder Input Slave Unit stores the  soft switch and the preset command value as output data, and can 
allocate required data to Output area.
The details of each data type are as follows.

Abbreviation

Status name

Operation

PACKn

Present value preset 
execution completed

Soft switch "Present value preset execution" completion flag
0

→

1: Preset execution completed

1

→

0: Soft switch "Present value preset execution" is set to 0

RACKn

Present value internal 
reset execution completed

Soft switch "Present value internal reset execution" completion 
flag
0

→

1: Reset execution completed

1

→

0: Soft switch "Present value reset execution" is set to 0

EXRESn

External reset generation 
flag

1: Turned ON at reset generation by external input/phase Z
0: Soft switch "present value external reset generation flag 

clear" is changed from 0 to 1

EXLAn

External latch A 
generation flag

1: Turned ON with external latch A event generation
0: Soft switch "external latch A generation flag clear" is 

changed from 0 to 1

EXLBn

External latch B 
generation flag

1: Turned ON with external latch B event generation
0: Soft switch "external latch B generation flag clear" is 

changed from 0 to 1

CERRn

Present value preset set 
value error

0: No setting error
1: Setting error generation

CRUNn

Counter operation state

0: Counter stopped
1: Counter operating

9-2-2

Output Data Allocation

Data

Size

Detail

Soft switch

4 bytes

Used to control the Encoder Input Slave Unit.

Preset command value

8 bytes

Specifies the value to be written over the counter present value data 
at preset execution.

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов