manualshive.com logo in svg

Omron GX-AD0471, Руководство пользователя, Страница: 70 / 394

Поделиться
Скачать
Omron GX-AD0471 Скачать руководство пользователя страница 70

5   EtherCAT Communications

5 - 4

GX-series EtherCAT Slave Unit User’s Manual

5-3

Communications State Transitions

The EtherCAT State Machine (ESM) indicates the state transition model of EtherCAT Slave Unit 
communications control. It is controlled by EtherCAT Master Unit. 

The following figure shows the communications state transitions from power ON.

State

SDO 

communi

cations

PDO 

transmiss

ion

PDO 

reception

Contents

Initialization (Init)

Not 
possible.

Not 
possible.

Not 
possible.

Communications are being initialized. 
Communications are not possible.

Pre-Operational
(Pre-Op)

Possible

Not 
possible.

Not 
possible.

SDO (message) communications are 
possible in this state. 
This state is entered after initialization has 
been completed. It is used to initialize 
network settings.

Safe-Operational
(Safe-Op)

Possible

Possible

Not 
possible.

In this state, PDO transmissions are possible 
in addition to SDO (message) 
communications. 
PDO sendings can be used to send 
information such as status from the Slave 
Unit.

Operational (Op)

Possible

Possible

Possible

Normal communication state
PDO communications can be used to control 
the I/O data. 

Initialization

Pre-Operational

Safe-Operational

Operational

Power ON

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов