manualshive.com logo in svg

Omron GX-AD0471, Руководство пользователя, Страница: 284 / 394

Поделиться
Скачать
Omron GX-AD0471 Скачать руководство пользователя страница 284

12   Troubleshooting and Maintenance

12 - 4

GX-series EtherCAT Slave Unit User’s Manual

Errors of EtherCAT Network

[PWR] 

indicator

[L/A IN]

[L/A OUT]

LED

[RUN] 

indicator

[ERR] 

indicator

Description

Cause

Actions

On

On

−

−

Link 
established in 
physical layer

Operation standby 
status after 
establishing link in 
physical layer.

−

On

Off

−

−

Link not 
established in 
physical layer

A link in physical 
layer has not been 
established.

After checking the 
following items, restart 
the Slave Unit according 
to the specification of 
connected EtherCAT 
Master Unit.

•

Is the 
communications 
cable wired correctly? 

•

Are any cables 
disconnected or loose 
in the part that 
connects to the 
connector? 

•

Is the cable length 
appropriate? 

•

Is the 
communications 
cable of the 
recommended 
specification?

The host master 
has not been 
started.

Check that EtherCAT 
Master Unit is operating 
correctly. If using an 
OMRON EtherCAT 
Master Unit, check the 
EtherCAT Master Unit 
mode and Slave Unit 
node addresses. If 
using EtherCAT Master 
Unit from another 
manufacturer, refer to 
the user's manual for 
that Master Unit.

A hardware failure 
occurred.

If the problem is not 
resolved even after the 
measures described 
above are taken, the 
Slave Unit hardware 
may be damaged. 
Replace the applicable 
Slave Unit.

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов