manualshive.com logo in svg

Omron GX-AD0471, Руководство пользователя, Страница: 283 / 394

Поделиться
Скачать
Omron GX-AD0471 Скачать руководство пользователя страница 283

12 - 3

12   Troubleshooting and Maintenance

GX-series EtherCAT Slave Unit User’s Manual

12-
1  T
rou
blesh

oo
ting

12

12-
1-1  Er

ror
s tha
t Can be C

hecked with Status Indicator and 

Action

s to 

Take

On

−

Off

On

Hardware error

A hardware failure 
occurred.

If the error does not 
clear even after the 
power is turned ON 
again, the Slave Unit 
hardware is damaged.
Replace the Slave Unit.

F

B

The Expansion 
Unit is 
disconnected.

Check the Expansion 
Unit connection.

On

−

−

B

Illegal switch 
setting

A range setting 
switch or other 
switch setting is 
illegal. 

Check the switch 
settings then restart the 
Slave Unit according to 
the specification of 
connected EtherCAT 
Master Unit.

Non-volatile 
memory data 
error

A non-volatile 
memory data error 
occurred.

Use the Configuration 
Tool or SDO 
communications to 
restore the default data 
and restart the Slave 
Unit according to the 
specification of 
connected EtherCAT 
Master Unit.

Sync manager 
setting error

The sync manager 
setting is illegal.

Change to the correct 
settings.

Hardware error

A hardware failure 
occurred.

If the problem is not 
resolved even after the 
measures described 
above are taken, the 
Slave Unit hardware 
may be damaged. 
Replace the applicable 
Slave Unit.

[PWR] 

indicator

[L/A IN]

[L/A OUT]

LED

[RUN] 

indicator

[ERR] 

indicator

Description

Cause

Actions

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов